Glass insulation coating construction steps
Lead: In modern home decoration, glass has become an indispensable home building material. It replaces the windows of ancient paper pastes. It has gradually developed into the present, but it has formed different styles and various types of products. Renovation needs in all aspects of the community. Today we are going to talk about the construction process of a thermal insulation coating. We all know that when we refer to the coating, we will think that it is used on the wall. But what about glass insulation paint? Let's take a look at it. What is glass insulation coating? Glass heat-insulating coating is a coating prepared by using various metal nano-powder materials. The nano-materials used have special optical properties, that is, high blocking ratio in the infrared and ultraviolet regions. The visible light region has a high transmittance. By using the transparent heat insulation properties of the material, it is mixed with environmentally-friendly high-performance resin, and processed through special processing to prepare an energy-saving and environmentally-friendly thermal insulation coating. Under the premise of not affecting the lighting of the glass, the energy saving effect is achieved in the summer and the energy saving effect is achieved in the winter. Glass insulation coating construction steps 1. Preparation: Wear overalls, wear plastic gloves, masks, goggles if necessary, and wear safety helmets and safety ropes for outdoor construction. Before starting construction, the safety personnel will check the safety performance of the hanging rails and the implementation of various safety measures for aerial work. After the safety conditions are met, the construction can be started after the on-site safety officer signs the construction and agrees to the construction. 2. Tool preparation: spray bottle, substrate treatment agent, scouring pad, alcohol, rag, glass scraper, protective tape, plastic protective film, tin foil, detergent, etc. 3. Protection of the curtain wall and window frame: Wipe the joint around the window frame with alcohol, attach a protective tape, cover the plastic film, so that the water or liquid will not get on the window frame. If it is necessary to cover the wall and the floor with a plastic film in the indoor construction, the edge of the joint is fixed with tape. 4. Substrate treatment: After weaving the scouring pad, apply a proper amount of the substrate treatment agent, spread it on the surface of the glass (or spray it on the surface of the coated glass with a spray device), rub and clean the surface, and scrape it with a glass spatula. 5. Alcohol cleaning: Apply evenly on the glass with a rag soaked in alcohol liquid. Pay attention to the liquid. After the alcohol has completely evaporated, spray it with a spray bottle to check if the glass is clean. After scraping with a glass knife, apply alcohol to allow the substrate impurities to evaporate again. 6. Smear method: Cut and install special sponge and metal frame according to the width of the glass. Then, the glass heat insulating coating and the curing agent are mixed in a certain ratio, and then injected into the long container. Next, apply the installed metal frame strip and sponge to apply the solution to the glass. 7. Drying and deodorization: dry touch, deodorization within 1 hour after finger touch drying. 8. Acceptance and finishing: Finger-drying acceptance is carried out in the inconspicuous part of the glass surface. After passing the test, the protective film is removed, and the plastic protective film, tape and other garbage are collected. Finally, the used chemicals are collected, and the quality of the thermal insulation coating is sampled and tested. The basic construction steps of the glass insulation coating are divided into the above eight steps. If you do all the above steps, your glass will have different effects. It will no longer be a common glass that blocks the wind and rain. It can make you feel cool in the summer, but keep your home warm in the winter. So quickly decorate your home glass, I believe you will get it easily after reading this article. Then, today's construction process for glass insulation coatings is here. [Follow the WeChat public number "Jiuzheng Paint Network"; pay attention to surprises, scan code to view "If your husband is selling paint..." Jiuzheng Coating Network Exchange Group] Ultra-Thin Ball Valve,Industrial Ultra-Thin Ball Valve,Thread Globe Valves,Threaded Swing Check Valve ZHITONG PIPE VALVE TECHNOLOGY CO.,LTD , https://www.ztongvalve.com
